Mustang GT350 Forums banner

Steeda Jacking Rails

9772 Views 17 Replies 6 Participants Last post by  HotLap
Installed the Steeda Jacking Rails this afternoon, easy peasy. Now I can finally get the car on Jack Stands and check to make sure the oil filter is torqued properly and make sure that all the screws are in the front splitter before hitting some track days.

Attachments

See less See more
1 - 18 of 18 Posts
Nice thinking about getting a set myself.
Is it a job you can do on driveway or do you need lift?

Any Pics?
I did this in my garage with a 15mm socket wrench and a small jack just hold the rail up to help start the bolts. Don't need the jack, but it made it a little easier. Takes about 30-45 minutes total.
Great looking color Bullitt40 and now you can jack it up and not worry
I did this in my garage with a 15mm socket wrench and a small jack just hold the rail up to help start the bolts. Don't need the jack, but it made it a little easier. Takes about 30-45 minutes total.
So a properly placed floor jack won’t hurt. Got the tools, thx.
Go to CJ Pony. They have a video on installation.
Put my jacking rails to use today, got the car up so I could ck to make sure the front splitter had all the fasteners installed. They were. Next I wanted to ck the screw on oil filter for proper torgue of 16 to 18 Ft pounds before going to a track day. I had asked the local ford dealer to ck that when they did the oil line recall and replacement. Well , the oil filter must have been hand screwed on and not checked. I put my torque wrench on the filter and was turned that sucker almost a turn and a half before it clicked at 17 Ft lbs. Dodged a bullet I believe.
They are a great choice & they are a very easy, bolt-in design:

[video=youtube;glgKEEGLcS8]https://www.youtube.com/watch?v=glgKEEGLcS8[/video]

If I can ever help with pricing - don't hesitate to email me at [email protected].

Best Regards,

TJ
Emailed you TJ
Emailed you TJ
Ditto TJ!!

TJ, not sure why but I couldn't get to your email so I PM'd you instead, thx!!
Ok here is the hook up for Forum members !!

"I can do 10% off either online with my code JC10 at checkout, or call in and ask for john and ill handle it over the phone"

Thanks John for the support for us!!!!
  • Like
Reactions: 2
Ok here is the hook up for Forum members !!

"I can do 10% off either online with my code JC10 at checkout, or call in and ask for john and ill handle it over the phone"

Thanks John for the support for us!!!!
Nice thanks Voodu for following up with TJ and thanks TJ at Steeda for the break!! Should we go to the Steeda site and do you have a stock number for the rails? I was there earlier and didn't see the exact product...thx!!
steeda # 555-5205
  • Like
Reactions: 1
Woo Hoo, ORDERED!! Called John directly and he gave me the discount, thanks to both Texas Voodu and Bullitt40!!
By the way I was also asking him about additional suspension mods for our cars and here's what he came back with:

1) G Track Brace (front sub frame) part # 5533
2) IRS subframe support brace Par #5754
3) IRS Subframe Alignment Kit for rear cradles part # 4438

Anyone have experience with these?
By the way I was also asking him about additional suspension mods for our cars and here's what he came back with:

1) G Track Brace (front sub frame) part # 5533
2) IRS subframe support brace Par #5754
3) IRS Subframe Alignment Kit for rear cradles part # 4438

Anyone have experience with these?
That's what I am ordering !!!
That's what I am ordering !!!
Nice, please post your progress, Sir! Voodu, are you going to have to have the rear aligned after assembling the IRS support and alignment kits?
1 - 18 of 18 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top